Cookie Einstellungen
Diese Webseite verwendet ausschließlich notwendige Cookies, die für das Funktionieren von Login und Cookie-Hinweis unbedingt erforderlich sind. Statistik- und Werbe-Cookies kommen nicht zum Einsatz. Weitere Informationen finden Sie in unserer Datenschutzerklärung.
OK
TPMC541
Add to Info-List

TPMC541 32/16 Single-Ended or 16/8 Differential A/D Channels, 8/4 Voltage & Current Range D/A Channels and 8 LVTTL/TTL Digital I/O Channels

Up to 32 single-ended or 16 differential channels of 16bit bipolar analog input; Input Voltage Ranges: ±0.64V, ±1.28V, ±2.56V, ±5.12V, ±10.24V, ±12.288V, ±20.48V (differential only), ±24.576V (differential only); Up to 8 channels of simultaneous update single-ended 16 bit unipolar/bipolar 16bit analog output; Output Voltage Ranges: 0 to 5V, 0 to 10V, ±5V, ±10V, 0 to 6V, 0 to 12V, ±6V, ±12V, Outout Current Ranges: 4 to 20mA, 0 to 20mA, 0 to 24mA; DMA functionality; Hardware Correction: Factory calibrated; Temperature Sensor on-board; Programmable conversion rates: can be output to other modules, can be input from other modules; Frame Trigger signal for synchronization purposes; 8 channels of tri-state 5V-tolerant LVTTL/TTL digital input/output, ESD protection; Mini D Ribbon (MDR68) type front I/O connector; Operating temperature: -40°C to +85°C (Forced Air Cooling required).

The TPMC541 is a standard single-wide PCI Mezzanine Card (PMC) compatible module providing:

  • A PCI Master capable 32 bit 33 MHz PCI interface
  • 8 Tristate-Capable bi-directional 5V-tolerant LVTTL/TTL compatible General Purpose Digital I/O Lines (Front I/O)
  • Up to 8 Single-Ended 16 bit Analog Outputs in (bipolar or unipolar) Voltage Mode or (unipolar) Current Mode (Front I/O)
  • Up to 32 Single-Ended or 16 Differential 16 bit bipolar Analog Inputs (Front I/O)
  • Tristate-Capable bi-directional 5V-tolerant LVTTL/TTL compatible Digital I/O Lines for Conversion Control Signals (Conversion Clock, Frame Trigger) (Rear-I/O)
Digital I/O
The TPMC541 features 8 ESD protected, interrupt and tristate-capable bi-directional general purpose digital I/O lines at the front I/O connector. Each digital I/O line features a pull resistor to a common reference (+3.3V, +5V or GND).

Analog Outputs
The TPMC541R-10R order option provides 8 (eight) analog output channels while the TPMC541R-20R order option provides 4 (four) analog output channels.

Each individual D/A channel can be configured to operate in any of the following output ranges:

  • 5V, 6V, 10V or 12V unipolar Voltage Ranges
  • ±5V, ±6V, ±10V or ±12V bipolar Voltage Ranges
  • 4mA to 20mA Current Range
  • 0mA to 20mA (or 24mA) Current Range
The TPMC541 provides a D/A Sequencer unit for performing periodic simultaneous digital to analog conversions at a configurable conversion rate.

Analog Inputs
The TPMC541R-10R order option provides 4 (four) ADAS3022 devices and up to 32 single-ended or 16 differential analog inputs. The TPMC541-20R order option provides 2 (two) ADAS3022 devices and up to 16 single-ended or 8 differential analog inputs.

Each ADC device configured for Single-Ended Input Configuration provides the following input voltage ranges (single-ended and referenced to ground): ±0.64V, ±1.28V, ±2.56V, ±5.12V, ±10.24V, ±12.288V. Each ADC device configured for Differential Input Configuration provides the following differential input voltage ranges: ±0.64V, ±1.28V, ±2.56V, ±5.12V, ±10.24V, ±20.48V, ±24.576V.

The TPMC541 provides an A/D Sequencer unit for performing a sequence of periodic analog to digital conversions at a configurable conversion rate.

Conversion Correction Data
Each TPMC541 is factory calibrated. Conversion data correction values are determined during the factory acceptance test and are stored in an on-board serial EEPROM unique to each PMC module. These correction values may be used to perform a hardware correction for every individual D/A channel and output range and for every individual A/D channel and input range.

Conversion Control Signals
Conversion clock signals may be generated on-board for internal use and may also be driven out on P14 rear I/O if the card is operating as a master card in a Multi-Board configuration. The conversion clock signals may also be sourced externally via the P14 rear I/O interface if the card is operating as a slave card in a Multi-Board configuration.

I/O Connector
The general purpose digital I/O signals, the analog output signals and the analog input signals are accessible on a 68 pos. Mini D Ribbon (MDR68) front connector.
Ordering Options
Manuf. Part No.  Product Description
TPMC541-10R  32 Single-Ended or 16 Differential A/D Channels, 8 Voltage & Current Range D/A Channels and 8 LVTTL/TTL Digital I/O Channels. Up to 32 Single-Ended or 16 Differential 16 Bit Analog Input Channels, 8 Single-Ended 16 Bit Voltage & Current Range Analog Output Channels and 8 LVTTL/TTL Digital I/O Channels, with MDR68 front panel I/O
TPMC541-20R  16 Single-Ended or 8 Differential A/D Channels, 4 Voltage & Current Range D/A Channels and 8 LVTTL/TTL Digital I/O Channels. Up to 16 Single-Ended or 8 Differential 16 Bit Analog Input Channels, 4 Single-Ended 16 Bit Voltage & Current Range Analog Output Channels and 8 LVTTL/TTL Digital I/O Channels, with MDR68 front panel I/O

Software and Documentation
Manuf. Part No.  Product Description
TPMC541-DOC  User Manual for TPMC541
TDRV019-SW-25  Integrity Software Support
TDRV019-SW-42  VxWorks Software Support (Legacy and VxBus-Enabled Software Support)
TDRV019-SW-65  Windows Software Support
TDRV019-SW-82  Linux Software Support
TDRV019-SW-95  QNX Software Support
For other operating systems please contact systerra.

Accessories
Manuf. Part No.  Product Description
TA113  MDR68 Cable
TA207  MDR68 Terminal Block
TA312  Cable Kit for Modules with MDR68 Connector
Return to last Page ...